Dirty dishes after a full cycle? It's often not the detergent or the machine itself—it could be your spray arms. When they get clogged with food particles, your dishwasher can't spray, rinse, or clean like it should.

Left unchecked, debris builds up fast in busy kitchens. It blocks the lower spray arm, fills the filter, and even affects the drain. Over time, this wears down your appliance and hurts your kitchen's performance and service quality.

In this How to Clean Dishwasher Spray Arms: Quick & Easy Guide, the team at Industry Kitchens shares simple steps to help you remove gunk, soak arms properly, and get your dishwasher working at full potential. Whether you're running a cafe or a large commercial kitchen, this guide helps you protect your racks, test spray strength, and fix flow problems before they cause a costly break.

Why Clean Dishwasher Spray Arms?

Spray arms are key to getting your dishes clean. They spin and spray soapy water to rinse off food particles from every rack, cup, and plate.

But over time, food, grease, and grime can build up. This is especially common around the lower spray arm, filters, and clips. Even if your machine says it's self-cleaning, that's not enough in a busy commercial kitchen.

Blocked spray arms reduce water flow and cleaning power. They can lead to poor wash performance or even damage your dishwasher.

You can protect your appliance and improve its performance by routinely cleaning the spray arms. Additionally, you prolong the life of your machine and lower the chance of malfunctions.

It's a small chore that helps lift your cleaning quality and keeps your service running smoothly. Think of it as basic security for your equipment.

Spray arms looking clogged? No amount of soap can fix that. Follow our guide:How to Deep Clean a Dishwasher.

Operating dishwasher spray arm with visible water jets, steam and cleaning holes during active dishwashing cycle for cleaning guide

How Blocked Spray Arms Ruin Wash Performance

When your spray arms get clogged, your dishwasher can't do its job properly. Bits of food, grease, or mineral build-up block the holes that spray soapy water, causing a big drop in cleaning power.

What can go wrong is as follows:

  • Reduced Water Flow – The arms can't spray evenly, so dishes on some racks stay dirty.

  • Dirty Dishes & Hygiene Risks – Leftover food and grime remain on plates, bowls, or utensils, especially in tight spaces.

  • Extra Strain on the Machine – Clogged arms make your appliance work harder, which can wear out the filter, motor, or even cause a break.

Even if your dishwasher filter is clean, clogged arms still interfere with your cycle. Twist, lift, and test your arms frequently; doing so can help catch issues early.

Imagine serving customers meals from dishes that were never properly cleaned — don't let that happen to your kitchen.

Top Signs Yours Need Attention

Is it time to question whether your spray arms require cleaning? Examine the following indicators:

✓ Dirty Dishes After Washing – If food or grime remains, your dishwasher may not be spraying properly.

✓ Weak Rinse or Residue – Leftover soapy water or streaks mean the spray isn't reaching all surfaces.

✓ Odd Noises – Grinding or thumping may signal blocked arms trying to spin.

✓ Uneven Cleaning – If only one rack gets clean, the lower or upper spray arm might be blocked.

✓ Clogged Dishwasher Filter – A full filter lets debris cycle back into the wash.

✓ No Recent Check – Haven't opened the door, removed a clip, or given the arms a shake lately? It's time.

Spotting issues early saves your appliance, improves performance, and avoids expensive service calls.

Still pulling out dirty plates after a wash? Your filter might be to blame. See How to Clean a Dishwasher Filter: Quick Guide for Aussie Kitchens.

Tools You'll Need

  • Soft-Bristled Brush – Great for scrubbing spray arms without scratching them.

  • Toothpicks or Skewers – Ideal for clearing food bits from spray holes.

  • White Vinegar – A natural solution that helps soak and loosen grime.

  • Baking Soda – Works with vinegar to break down grease and build-up.

  • Small Bucket or Sink – For soaking spray arms in a cleaning mix.

  • Dish Gloves –Protect your hands while cleaning inside the machine.

  • Microfibre Cloth – For wiping down the filter, racks, and door edges.

  • Screwdriver (if needed) – Some spray arms have clips or screws to lift or twist.

These simple tools help keep your dishwasher running smoothly and your dishes spotless.

Aussie-Friendly Items: White Vinegar, Toothpicks, Soft Brush

You don't need fancy products to clean your dishwasher. White vinegar is a great natural solution for cleaning spray arms and the dishwasher filter. It helps break down grime and remove odours inside the machine.

Toothpicks work well to loosen food from small spray holes. A soft brush gently scrubs without damaging the appliance. These common items make it easy to clean behind the door without additional expenses.

Simply take off the clip, shake it well, and pop everything back in place. A simple routine like this keeps your unit operating without disruptions while sustaining optimal wash functionality.

Bottom spray arm component with visible water holes positioned above mesh dish basket during dishwasher cleaning cycle process

Step 1: Clear Debris & Detach Spray Arms Safely

  1. Keep the door open and remove the bottom rack for better access.

  2. Gently twist or unclip the spray arms—some may lift straight out while others need a little wiggle.

  3. Shake out any loose bits of food or grime stuck inside the arms.

Pro Tip: Don't force it—always check for a locking clip to avoid breaking your appliance.

Step 2: Inspecting for Clogs

Check each spray hole for clogs from food, grease, or hard water buildup. These can mess with your machine's ability to wash dishes properly.

  • Look for blocked spray holes

  • Check for greasy residue

  • Listen for rattles when you shake the arm (a sign of trapped bits)

Step 3: Soak and Scrub Spray Arms with Vinegar & Baking Soda

  1. Fill a deep sink or dishwasher-safe bowl with warm water and white vinegar.

  2. Soak the arms for 15–30 minutes to help dissolve grime.

  3. Add a bit of baking soda and use a soft brush to clean the holes gently.

  4. Rinse thoroughly before drying.

This solution is safe for plastic and tough on buildup—perfect for busy kitchens.

Step 4: Clean Your Dishwasher Filter Too

While the spray arms are soaking, take a moment to remove and rinse the dishwasher filter. A quick clean keeps your machine from clogging again and helps improve every wash.

A clean filter also stops food bits from blocking your freshly scrubbed arms.

Step 5: Reattaching & Testing

  • Pop the arms back in place with a gentle click or twist.

  • Spin them by hand to check they move freely.

  • Run a quick rinse or light wash cycle to test water flow.

That's it—your appliance is now ready to get back to serious cleaning.

Industry Kitchens Hobart undercounter dishwasher with integrated dryer - front and side view showing commercial kitchen equipment

Keeping Spray Arms Clean Long-Term

  • Rinse off food scraps before loading to prevent clogs and build-up.

  • If the dishwasher isn't full, run a quick rinse cycle to stop food from drying on.

  • Clean the filter weekly to avoid debris recirculating through the spray arms.

  • Inspect the spray arms monthly—shake gently and check for blockages.

  • Run a monthly empty cycle with a descaler to reduce grease and mineral build-up.

  • Use a water softener in hard water areas to prevent scaling.

  • Leave the door slightly open after the last wash to reduce odours and moisture.

These quick habits help your machine stay clean and wash better every time.

When to Call a Pro

Sometimes, cleaning just isn't enough. If your spray arms still won't spin properly after a full clean—or if you notice visible cracks, leaks, or broken clips—it's time to get expert help.

These signs could mean deeper issues with the appliance that a technician needs to handle. In busy commercial kitchens, regular servicing is a smart move to avoid bigger problems and costly downtime.

DIY Fixes

Call a Pro If

Food debris in spray holes

Cracks or splits in the spray arms

The filter needs a rinse or scrub

Spray arms won't click or stay in place

Water flow seems low, but improves after a clean

Spray arm leaks or fails to spin freely

Minor grease or buildup

Repeated clogs even after full cleaning

Pro Tip:

In high-volume commercial kitchens, aim to get your dishwasher serviced every 6 to 12 months. Frequent inspections keep your machine operating smoothly and prevent unplanned breakdowns by identifying worn parts early.

Tried cleaning everything, but the dishes still come out dirty? Check Why Is My Dishwasher Not Cleaning Properly?

Conclusion

Clean spray arms help your dishwasher do what it's meant to—wash dishes properly. In busy commercial kitchens, this simple task keeps your machine running at full power. It also protects your appliance from damage caused by food, grease, or clogs.

Don't wait for breakdowns to start cleaning. With regular care and smart habits, you can avoid service delays, protect water flow, and keep hygiene standards high. The team at Industry Kitchens recommends making spray arm checks part of your routine maintenance.

Whether you run a café or manage a large kitchen, keeping things clean behind the door makes all the difference.

Regular spray arm checks are a simple way to keep your dishwasher running smoothly. Whether you're using an underbench, passthrough, or conveyor-style model, consistent care helps maintain performance across all types of commercial dishwashers.

Frequently Asked Questions

How to remove grime from dishwasher spray arms?

If your dishwasher spray arms are clogged with food particles or mineral deposits, you'll need to give them a proper deep clean. First, twist off the lower spray arm and any upper arms, then soak them in a mix of warm water, vinegar, and baking soda in a dishwasher-safe bowl for a few hours. Use a toothpick or soft brush to remove any gunk or debris stuck in the holes, rinse well with cold water, and test the spin before putting them back.

Is it possible to clean dishwasher spray arms with vinegar?

Yes, vinegar is a great way to clean dishwasher spray arms, especially if there are deposits of hard water or grease. Just soak the spray arms in hot water and vinegar for a few hours to help remove food debris, mineral deposits, and detergent buildup. It's an easy and safe way to get the most out of your appliance.

Do dishwasher arms need to be cleaned?

Yes, you definitely should clean your dishwasher arms regularly. Over time, food particles, grease, and hard water can clog the holes, stopping the spray arms from distributing water properly during a wash cycle. a quick deep clean every two months helps shield your dishes and utensils from food residue.

How to tell if dishwasher spray arms are clogged?

If your dishes come out dirty or you notice uneven rinsing, your spray arms might be clogged. Check if the arms spin freely and look closely at the holes—debris, grease, or hard water may be blocking them. You might also hear a louder-than-usual cycle if water isn't spraying properly.

How often should I clean dishwasher spray arms?

To keep your dishwasher working at its best, it's smart to clean the spray arms every 1–2 months, especially if you live in a hard water area. Regular cleaning helps eliminate food, grease, and hard water deposits, stops the holes from getting blocked, and keeps the water spray strong. Make it part of your usual filter and tub maintenance routine to avoid a big repair job later.



Read More: